Remote-processing RPC-330 Manuel d'utilisateur télécharger pdf (Page 8)

SETUP AND OPERATION SECTION 2

Page 2-2 RPC-330

FIRST TIME OPERATION

Become familiar with the locations of connectors before

getting started. See Figure 2-1.

RPC -330 jump ers have been set at the factory to operate

the system immediately. For first time operation, do not

install any connectors or parts unless specified below.

Jumpers should be kept in default positions.

1. Connect power.

The RPC-330 needs + 5 ±0.25 volts at 300 ma.

Any well regulated supply that supp lies this will

work. Be careful when using "switching" power

supplies. Some of the se supplies do not regulate

properly unless they are adequately loaded. Don' t

forget that power requirements increase w hen opto

modules are used. G4 opto m odules require up to

20 ma each.

Make sure pow er is off. Connect the power supply

to one of the appropriately marked terminals on the

RPC-330. There three pow er connectors: P 2, P3,

and P6. Any one may be used to connect power.

2. Hook up to a PC or terminal.

You can use either a PC or CRT term inal to

program the RPC-330. Connect one end of the

VTC-9F connector to the 10 pin COM0 port on the

RPC-330. Refer to Figure 2-1 for connector

location.

Using a PC

Connect the VTC-9F serial cable to the PC's COM1

or COM 2 port. Y ou may need a 9 pin male to 25

pin female adapter. The VTC-9F is designed to

plug directly into the 9 pin serial port connector on a

PC.

Start up your serial communication program. Set

comm unication par ameter s to 9600 baud, 8 da ta

bits, no parity, 1 stop.

Using a Terminal

Follow your terminal instructions to set the baud

rate to 9600 baud, 8 data bits, no parity, and 1 stop.

You may need a 9 pin male to 25 pin male adapter

to connect the VTC-9F.

3. Power up.

Turn on your power supply. On power up a

RPBASIC-52 V1.09

RPC-330

Bytes free: 63740

65,536 bytes of additional expanded memory detected

512K byte EPROM installed

If a nonsense message appears, your terminal or PC

may not be set to the appropriate communication

parameters. If the system still does not respond,

refer to TROUBLESHOOTING later in this section.

4. Testing.

The system is now in the " imme diate mode" and is

ready for you to start programming. T ype the

following program:

10 FOR X=0 TO 2

20 PRINT "Hello ",

30 NEXT

40 PRINT

Now type RUN

The system will display:

Hello Hello Hello

READY

Terminate a program by typing a < Ctrl> -C.

UPLOADING AND DOWNLOADING

PROGRAMS

Downloading program s means transferring them from

your PC (or terminal) to the RPC-330. Uploading

means transferring them from the RPC -330 back to the

PC. This section explains how to do both of these

procedures using generalized instructions for terminal

programs (Procomm , Windows Ter minal, etc.)

When uploading or downloading files, select ASCII text

format. XMODEM, YMODEM, or other formats are

not used.

RPBASIC-52 does not know when you are typing in a

program or if something else (laptop or mainfr ame) is

sending it char acters. The uploa d and dow nload file

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 47 48

Commentaires sur ces manuels

Pas de commentaire

Remote-processing RPC-330 Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Ordinateurs Remote-processing RPC-330